CHINESE Seamless Gutter Downspout & Elbow HVAC Roof Panel Slitters & Brakes About Us

Standing Seam Roof Panel

SSH PANEL MACHINE

We welcome your questions and comments.

Please e-mail us at liberty@penn.com

INFINITELY ADJUSTABLE PANEL WIDTHS FROM 12" - 20"

Comes standard with the following:

  • New & improved EZE CHANGE? Profile system (complete changeover in 30 minutes or less)
  • Hydraulic Drive and Shear
  • Quick Change Power Pac? wiht 16 HP Electric Start Gasoline Engine or 7.5 HP 220V Three Phase Motor
  • Two Sets of Bead, Pencil, or V-Rib Rollers
  • Forms 30 - 24 ga. Steel, .019 - .040 Aluminum, 16 oz. - 20 oz. 3/4 Hard copper with coils up to 24 inches wide
  • Optionial Computer Batch and Length Control with Panel Recognition Photo Eye
  • Approximately 60 feet per Minute Panel Speed
  • Limited 3 Year Parts/ 1 Year Labor
  • Limited Lifetime Separation on Drive Rollers
  • Limited Lifetime on Stainless Steel Forming Rollers

 

  • Runs Steel from 24 to 30 gauge
  • Runs Copper, Aluminum, Steel
  • Snap-lock, Mechanical Seam, T Panel, ARMCO style and Bermuda Profiles
  • Clip Relief and/or Stiffening can be added to any Panel Profile Striated Paneling Rollers also available
  • Separate drive and form rollers eliminates most oil canning

    This means better products, less problems, and lower costs.

Specifications

Panformer

Length - 12' (3.657m)

Width - 4"5" (1.346m) plus engine projection

Height - 1'3" (.381m) plus engine projection

Weight - 2010 lbs. (912kg)

Features

The Standing Seam Power Panel machine makes various standing seam roof pans in any width from 12" - 24", depending on the panel configuration. It will accept coil widths from 16" to 28". The machine is complete with a hydraulic drive system and cast polyurethane drive rollers, 16 H.P. electric start gasoline engine, hydraulic shear that cuts any width panel, remote limit switch, 2 sets of bead rollers, and a single remote decoiler stand. It requires a forming roller system to produce panels. Prewiring for later addition of sealant pump system is included.

Panformer on Trailer

Length - 17'2" (5.232m)

Width - 7'3" (2.21m)

Height - 6'3" (1.905m) with reel

Weight - 3990 lbs (1810kg)

Stainless steel forming roller systems on mounting bars are available as follows:

SS100 Makes 1" high x .5" wide mechanically seamed panel leg

SS150 Makes 1.5" high x .5" wide mechanically seamed panel leg

A hand seamer comes with each of the above systems.

Power

16 H.P. Electric Start Gas Engine

SS550 Makes 1.5" h x 7/17" wide SNAP-LOCK I snap seam panel. The most positive engagement available.

Drive

hydraulically powered chain driven cast polyurethane drive rollers

SS675 Makes 1.75" high x 7/16" wide SNAP-LOCK II snap seam panel.

Shear

Electrically activated, hydraulically powered, infinitely adjustable full cycle with safety interlock/stop

FF100 Roller system to make 1" high snap lock seamed panel with slotted nailer leg for clipless installation.

BP Roller System on mounting bars and cut-off dies to make Horizontal Bermuda Panels. Panels can have a or 1.5" bottom edge and have 11.5" or wider exposure.

Speed

Approximately 75ft/min. Speed should be decreased 25-50% when using sealant pump depending on temperature

Available Options

TA12 12,000# capacity tandem axle trailer. Has dual reel overhead decoiler standard. No remote decoiler will be furnished.

Materials Formed

Steel - 30 - 24 gauge (painted, galvanized)

Aluminum .019 to .040

Copper 16 oz. to 20 oz.

Profile and Machine Comparison


Select X mark to connect to .PDF drawing for each panel
Requires that Adobe Reader be installed

  SSP SSH SSR FWM

SS100
X X X  

SS150
X X X  

SS200
X      

SS210A
X      

SS450
X X X  

SS550
X      

SS675
X      

FF100
X X X  
  SSP SSH SSR FWM

BP 1"
X X X  

BP 1-1/2"
X X X  

T PAN
X X X  

FW1
      X

1" Soffit
      X

Bead Ribs
X X X X

Pencil Ribs
X X X X

V-Ribs
X X X X

Striation Ribs
X X X  

Clip Relief
X X X  
  SSP SSH SSR FWM
= UL 90 Rated


(click for the free downloadto read pdf files)